USA Worldwide The foundation for assay consolidation, future scalability and growth Add the Panther system to your lab and the capability to consolidate menu on a fully automated system, load samples in any order at any time, eliminate batch constraints and decrease turnaround time.
The foundation for assay consolidation, future scalability and growth Add the Panther system to your lab and the capability to consolidate menu on a fully automated system, load samples in any order at any time, eliminate batch constraints and decrease turnaround time. Want Image Slider on Tab Click.
Contact Us. Related Products. Previous Next. Adds flexibility, capacity and expanded menu, plus the ability to run laboratory developed tests. Learn More. Adds further capacity, walkaway time and throughput in 24 hours. Virtually connect your Panther systems to share information and monitor your lab from a centralized dashboard. Physically connect your Panther systems to grow testing volumes without increasing staff. HIV-1 Quant Dx. Mycoplasma genitalium. If this firearm is carelessly or improperly handled, unintentional discharge could result and could cause personal injury, death or damage to property.
Children are attracted to and can operate firearms that can cause severe injuries or death. Prevent child access by always keeping guns locked away and unloaded when not in use. If you keep a loaded firearm where a child obtains and improperly uses it, you may be fined or sent to prison. Ellos pueden causarse lesiones graves y la muerte. DPMS shall not be responsible for personal injury, death or damage to property resulting from either intentional or accidental discharge of this firearm, or from its function when used for purposes or subjected to treatment for which it was not designed.
DPMS will not honor claims involving this firearm which result from careless or improper handling, unauthorized adjustment or parts replacement, corrosion, neglect, or the use of wrong caliber ammunition, other than original high quality commercially manufactured ammunition in good condition, or any combination thereof. DPMS will not honor claims involving this firearm for any reason or cause when the second or subsequent owner makes such claims.
Before the rifle left the factory, this firearm was tested, carefully inspected and packaged. DPMS cannot control product handling after it leaves the factory; therefore please examine this firearm carefully at the time of purchase to ensure that it is unloaded and undamaged. Always make sure your firearm is not loaded and the bolt is latched open and to the rear before laying it down or handing it to someone else.
Always keep safety on "SAFE" when firearm is loaded and a round is chambered until ready to shoot. Be sure the cam pin is installed in the bolt group. If it isn't, your rifle can still fire but it could possibly explode, causing you personal injury or harm.
Applies only to the. DO NOT exchange or switch bolt assemblies from one rifle to another. It could cause personal injury to you and others and damages to your rifle. If your firearm fails to fire, hold it, keep it pointed towards the target and wait 30 seconds. If a hangfire has occurred, the round will fire within 30 seconds. If the round does not fire, remove magazine, eject round and examine the primer. If firing pin indent is light, misaligned or non-existent, have your firearm examined by a competent gunsmith.
If firing pin indent on primer appears normal in comparison to previously fired rounds assume faulty ammunition; appropriately dispose of misfired round from other live ammunition; reload and resume firing. When set to "FIRE" the firearm will fire a single shot each time the trigger is squeezed. When set to "SAFE" a cam bears upon the rear of the trigger, blocking movements and preventing the hammer from being released. Rifle will not fire. Selector lever cannot be on safe unless rifle is cocked.
Always place on SAFE when loading and unloading. SAFE Note: Remove magazine and make sure your rifle is unloaded and there is no ammunition in the chamber. Point in safe direction. Pull charging handle to rear and release. Place on safe. Pull trigger. Hammer should not fall. FIRE Note: Remove magazine and make sure your rifle is unloaded and there is no ammunition in the chamber.
Place selector on fire. Pull trigger and hold to rear. Hammer should fall. Release trigger and pull again. The disconnector, a part of the firing mechanism, prevents the firearm from firing full automatic. As the hammer is cocked after each shot the disconnector holds the hammer until the trigger is released.
When the trigger is released, retention of hammer passes from disconnector to trigger ready for the next shot. The bolt carrier assembly, located within the upper receiver, is designed to prevent the firing pin from striking a cartridge until the bolt is locked to the barrel. The following sections contain caliber specific information.
Please open to the section relevant to your particular rifle's caliber. If you are unsure of the caliber of the rifle, the caliber marking can be found on the barrel of the rifle, immediately in front of the gas block on the bottom of the barrel. Everyone should read page 36 for additional information pertaining to the Three Year Limited Warranty and returns!
Panther Pump Action Rifle. Panther Pump Action Pistol. Rear sight can be adjusted for both windage and elevation and has a dual aperture peep sight, one for short range and one for long range. When flipped forward, the aperture is marked O-2 for zero to meters. When the aperture is flipped back, it is set for using the long range sight. There are click settings in between for fine tuning. The windage knob is located on the right side of the rear sight. To adjust for horizontal movement on target, turn knob clockwise for right and counter-clockwise for left.
The front sight is adjustable for elevation zeroing only, it is not used at any other time in firing. To raise strike of bullet, rotate post in the direction of arrow marked up. Reverse the direction of rotation to lower strike of bullet. Each graduation notch moves the point of impact of bullet as indicated in chart. This procedure is for. For our rifles chambered in 7. The procedure described is for zeroing at 25 meters but may be adjusted accordingly for longer ranges. The following table shows change of impact per click at specific range.
No further adjustment should be made during zeroing. Set aperture to mechanical zero by adjusting windage until sight is aligned with center line on scale under sight. Carefully aim and fire at bull's-eye on target at 25 meters: Fire ten rounds to establish a group. Calculate clicks of windage required to move impact appropriate distance. Turn windage knob accordingly.
Calculate clicks of front sight required to raise or lower impact appropriate distance. Depress plunger and front sight required number of clicks. Clockwise will lower sight and raise impact, and counter-clockwise will raise sight and lower impact.
To battlesight zero your rifle, you adjust your sights so you can hit an aiming point at meters. Zeroing can also be accomplished on a 25 meter range by adjusting the sights so that the bullet will strike 2.
Forcing damaged ammunition into the chamber could result in personal injury or death to you and others and damage your rifle and property. The use of reloaded, hand-loaded or high pressure ammunition can be dangerous and will void the warranty. With front of magazine forward, place a round between the lips of the magazine with the bullet forward.
Press the round down until it is retained by the magazine lips. Place the next round on top of the last and repeat until desired number is loaded. Make sure the rifle is pointed in a safe direction and the safety is engaged at all times while loading the rifle. NEVER allow your fingers or other objects to contact the trigger while loading or unloading the rifle. Do NOT disengage the safety until you are ready to fire and have the rifle pointed safely downrange.
Press in on bottom of bolt catch while pulling back on charging handle, to cock the hammer and leave the bolt and carrier to the rear. With the bullets pointing forward, insert loaded magazine into magazine well and push it in until it stops and is retained by magazine catch.
0コメント